Garmin Active Speaker, Silver Manual de Instalação descarregar pdf (Página 2)

2

GHS 10 Active Speaker Installation Instructions

 Wearsafetygogglesandadustmaskwhendrilling,cutting,orsanding.

Contact Garmin

ContactGarminProductSupportifyouhaveanyquestionswhileinstallingyourGHS10Active

Speaker.IntheUSA,gotowww.garmin.com/support,orcontactGarminUSAbyphoneat(913)

397.8200or(800)800.1020.

IntheUK,contactGarmin(Europe)Ltd.byphoneat08082380000.

InEurope,gotowww.garmin.com/supportandclickforin-countrysupport

information,orcontactGarmin(Europe)Ltd.byphoneat+44(0)870.8501241.

Tools Needed

• Drillanddrillbits

• Number2Phillipsscrewdriver

• 3

in.(90mm)holesaw

•

in.(21mm)oranadjustablewrench

Choosing an Installation Location

TheGHS10activespeakerconnectstoyourcompatibleGarminVHFradiobetweentheradio

andtheGHS10handset.Whenplanningtheactivespeakerinstallation,considerthefollowing:

• PerFCClaw,youmustinstalltheGHS10(ifitistheprimarystation)inthewheelhouseorin

anadjacentroom.

• InstalltheGHS10andtheactivespeakeratleast20in.(.5m)fromanycompass.

• Installtheactivespeakerwithin48in.(1.2m)ofthelocationatwhichyoumountthe

bulkheadpass-throughplate.

• Ifthecableisnotlongenoughtoreachtheactivespeakermountinglocationfromtheradio,

extensioncablesareavailableinlengthsof16ft.(5m)and32ft.(10m).Installcable

extensionsbetweentheGHS10cableandtheradioaccordingtothelayoutdiagram.

• DonotconnectapassivespeakertotheGHS10cable.Cutandtapethebarepassive-speaker

wires.

Installing the GHS 10 Active Speaker

1. Remove the paper backing from the self-adhesive GHS 10 active speaker ush-mount template and adhere it to the bulkhead in a suitable

location..

2. Use a 3

in. (90 mm) hole saw to cut the opening as indicated on the template.

3. Place the speaker in the cutout.

4. Ensure that the mounting screw locations align with the holes marked on the template. If they do not, mark the locations of new pilot holes.

5. Drill four

in. (3 mm) pilot holes in the correct location. A

in. (3 mm) pilot hole is nominal for plywood. Different dashboard materials may

require different size pilot holes.

6. Use the included M4.2×25 screws to mount the active speaker.

7. Snap the cover plates on the active speaker.

8. To connect the active speaker wiring harness to the radio, use the

GHS 10 cable according to the layout diagram.

• Do not connect a passive speaker to the GHS 10 cable that you use

with the active speaker. Cut and tape the two bare passive-speaker

wires.

VHF 300 Series Layout Diagram

CompatibleGarmin

VHFradio

GHS10

GHS10active

speaker

Bulkheadpass-

throughplate

GHS10

cable

GHS10cable

extension

(optional)

Cutandtape

barewires

Active

speaker

cable

➊

➋

➌

➍

➊

Coverplates(2)

➋

M4.2×25screws(×4)

➌

Activespeaker

➍

Bulkhead

Mounting the Active Speaker

1 2 3 4 5 6 7 ... 15 16

Comentários a estes Manuais

Sem comentários

Garmin Active Speaker, Silver Manual de Instalação Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com não Garmin Active Speaker, Silver